The TEP V4.2x

The Time Energy Pump project

created on 09/04/97 - JLN Labs - last update on 09/08/97

Hi All,

After a short period of stand back and some "brainstorming" with the TEP Teamwork, I have decided today to go backward (or forward...this depends of the point of view ) about the TEP project and focus my research on the real parametric effect in a bifilar coil as I had begun with the TEP V2 and V3.

I think that my original design of the Tep (Series 2 and 3) is really close to the original Time Energy Pump concept than the TEP V4.2x.

To summarize the tests with the TEP 4.2x device (see the main scheme):

The TEP V4.2x shows interesting characteristcs like :

• A High Voltage Output (about 215 Volts) with a turns ratio between primary and secondary coils about 1 ( 0.98 ) compared to a normal transformer which would have a turns ratio about 18:1 ( 215:12)
• A very low reciprocal effect.
• The Voltage amplification effect is produced only with the bifilar coil configuration.
• The generated HV voltage seems only limited by the reverse voltage of the diodes and the wires insulation of the coils.
• The TEP V4.21 seems a very powerfull HV generator which uses the flyback effect in a bifilar coil but there is a conventional explanation for the functionning. I think today that this not the good way for achieving successfully an Overunity device.

Don't forget that the main purpose of the TEP device is to act as a Time Energy Pump Vs ZPE ( Zero Point Energy ).

You will find bellow some guide lines of the TEP concept.

The main principle of the TEP device may be decomposed as this :

- Using the parametric effect in a bifilar coil as an energy pump. When the circuit is closed on the Bifilar coil, the inductance drops rapidly near zero and the energy strored in the coil increases dramaticaly. During this energy growth in the TEP, I think that a kind of "siphon effect" must act in the TEP coils Vs ZPE (Zero Point Energy). This "siphon effect" will tap additional ZPE energy like a vaccum pump using water.

The additional energy tapped in the ZPE ( with the parametric effect in the TEP ) seems the only way to "regauge" the system and achieve an Overunity device.

Unlike a mechanical device ( the SMOT/RMOD device or an Overunity Magnetic motor ) which uses gravity or a little magnetic pulse to regauge itself, the TEP uses the parametric effect as a "siphon" Vs ZPE to regauge itself.

The disruption effect due to the parametric effect in the bifilar modifies the time constant of the circuit (L/R), thus the energy flows. The disymetry between the S-Flow (Poynting flow) running outside and the Time Flow compression inside the circuit (time constant compression) is the main cause of the Pumping effect in the ZPE. Today, I think that the TEP is "a way" to achieve a good Overunity device.

Today the TEP uses bifilar coils technologies in parametric conditions, but tomorrow, other kinds of process could be used to pump the Zero Point Energy. The only purpose of the TEP device is the creation of a disymetrical flow of energy between the outside flow energy (Poynting S-Flow) and the inside ( current flow in the wires ) during the energy flow from Source to Load and I think, today, that it is a good way to Free Energy.

The main advantage of the TEP is that it is a solid state device with no moving parts.

There is a great number of regauging steps due to the working frequency, thus the ZPE energy tapped may be enormous.

If you want to contribute to the development of the TEP project or simply to receive update informations on the TEP project, let me know with an Email

I hope that I shall be able to update my web site about a new release of the TEP soon, which will be the TEP V5.0.

Sincerely,

Jean-Louis Naudin ( France / GMT+1 )